Программы с открытым кодом для работы с программаторами TL866 в Linux.

Основная программа minipro, программа miniprohex предназначена для вызова minipro после преобразования файлов известных типов в бинарный формат для записи или преобразования бинарных файлов после чтения данных из микросхемы.

David Griffith / minipro · GitLab (An open source program for controlling the MiniPRO TL866xx series of chip programmers)

Установка необходимых пакетов

sudo apt-get install build-essential pkg-config git libusb-1.0-0-dev

1. Загрузка исходного кода и компиляция, копирование правил udev:

minipro_compile.sh

#!/bin/bash
git clone https://gitlab.com/DavidGriffith/minipro.git
cd minipro
make
sudo make install
 
sudo cp udev/*.rules /etc/udev/rules.d/
sudo udevadm trigger

miniprohex by Al Williams http://www.awce.com

Синтаксис:

miniprohex [--offset offset] [--unfill byte size] [--obs blksize] [--line-length length] [minipro_options] -r filename.ext

miniprohex [--offset offset] [minipro_options] -w filename.ext

Параметры:

Предполагается, что пути к minipro и srec_cat (из пакета SRecord) находятся в переменной окружения PATH.

minipro --hardware_check

Примеры вывода:

• Тест завершён успешно

  Тест завершён успешно

  Found TL866II+ 04.2.123 (0x27b)
  VPP driver pin 1 is OK
  VPP driver pin 2 is OK
  VPP driver pin 3 is OK
  VPP driver pin 4 is OK
  VPP driver pin 5 is OK
  VPP driver pin 6 is OK
  VPP driver pin 7 is OK
  VPP driver pin 8 is OK
  VPP driver pin 9 is OK
  VPP driver pin 10 is OK
  VPP driver pin 30 is OK
  VPP driver pin 31 is OK
  VPP driver pin 32 is OK
  VPP driver pin 33 is OK
  VPP driver pin 34 is OK
  VPP driver pin 35 is OK
  VPP driver pin 36 is OK
  VPP driver pin 37 is OK
  VPP driver pin 38 is OK
  VPP driver pin 39 is OK
  VPP driver pin 40 is OK
  
  VCC driver pin 1 is OK
  VCC driver pin 2 is OK
  VCC driver pin 3 is OK
  VCC driver pin 4 is OK
  VCC driver pin 5 is OK
  VCC driver pin 6 is OK
  VCC driver pin 7 is OK
  VCC driver pin 8 is OK
  VCC driver pin 9 is OK
  VCC driver pin 10 is OK
  VCC driver pin 11 is OK
  VCC driver pin 12 is OK
  VCC driver pin 13 is OK
  VCC driver pin 14 is OK
  VCC driver pin 15 is OK
  VCC driver pin 16 is OK
  VCC driver pin 25 is OK
  VCC driver pin 26 is OK
  VCC driver pin 27 is OK
  VCC driver pin 28 is OK
  VCC driver pin 29 is OK
  VCC driver pin 30 is OK
  VCC driver pin 31 is OK
  VCC driver pin 32 is OK
  VCC driver pin 33 is OK
  VCC driver pin 34 is OK
  VCC driver pin 35 is OK
  VCC driver pin 36 is OK
  VCC driver pin 37 is OK
  VCC driver pin 38 is OK
  VCC driver pin 39 is OK
  VCC driver pin 40 is OK
  
  GND driver pin 1 is OK
  GND driver pin 2 is OK
  GND driver pin 3 is OK
  GND driver pin 4 is OK
  GND driver pin 5 is OK
  GND driver pin 6 is OK
  GND driver pin 7 is OK
  GND driver pin 8 is OK
  GND driver pin 9 is OK
  GND driver pin 10 is OK
  GND driver pin 11 is OK
  GND driver pin 12 is OK
  GND driver pin 13 is OK
  GND driver pin 14 is OK
  GND driver pin 15 is OK
  GND driver pin 16 is OK
  GND driver pin 20 is OK
  GND driver pin 21 is OK
  GND driver pin 25 is OK
  GND driver pin 26 is OK
  GND driver pin 27 is OK
  GND driver pin 28 is OK
  GND driver pin 29 is OK
  GND driver pin 30 is OK
  GND driver pin 31 is OK
  GND driver pin 32 is OK
  GND driver pin 33 is OK
  GND driver pin 34 is OK
  GND driver pin 35 is OK
  GND driver pin 36 is OK
  GND driver pin 37 is OK
  GND driver pin 38 is OK
  GND driver pin 39 is OK
  GND driver pin 40 is OK
  
  
  VPP overcurrent protection is OK.
  VCC overcurrent protection is OK.
  
  Hardware test completed successfully!

• Программатор не подключён:

  No programmer found.

minipro --list|grep W27C512

вывод:

Found TL866II+ 04.2.123 (0x27b)
W27C512@DIP28
W27C512@PLCC32

Необходимо указывать полное название микросхемы, включая тип корпуса:

minipro --device W27C512@DIP28 --read dump.bin

minipro --device W27C512@DIP28 --verify dump.bin

Проверка на наличие данных в микросхеме:

minipro --device W27C512@DIP28 --blank_check

minipro --device W27C512@DIP28 --erase

minipro --device W27C512@DIP28 --write data.bin

minipro --update ФАЙЛ

ФАЙЛ можно взять из установленной версии программы Xgpro:

• для TL866 — update.dat
• для TL866II+ — updateII.dat